Maxi Life Electric Water Heater Faucet

Very comfortable electric hot water faucet in kitchen and bathroom

T1

This productNot suitable for outdoor use.

__t2__the first time you use, __t3__.

__t4__outlet water temperature __t5__.

__t6__no faucet, valve or similar equipment that could block or restrict the flow of water must be connected to the water outlet.

__t7__the faucet tip/nozzle should be cleaned regularly, before cleaning __t8__.

To prevent the risk of electric shock, use an electric faucet.

__t11__if the water inside the faucet freezes, the product will __t12__.

__t13__ of the product is __t14__. do not use the product if there is no earthing.

__t15__product working water pressure should be in __t16__range.

__t17__after each use, hold the button for about __t18__ this process:

__t19__reduce the risk of scalding caused by excessively hot water at next use.

__t20__helps reduce scale build-up.

__t21__extends the service life of the heating element.

__t22__if the electrical cord is damaged, the cord is __t23__.

__t24__when using an electric faucet, avoid using appliances on the same electrical circuit, such as air conditioners, induction cooktops, or electric water heaters.__t25__

__t26__ should be used in electrical connections in accordance with fixed installation rules __t27__

Preparation before installation

Because this faucet has high electrical power, before installation:

• Electricity meter,
• Insurance,
• Automatic switch/circuit breaker,
• Electrical installation

Should be checked.

The capacity of this equipment, the faucet __t29__.

Make sure you have __t30__ in the receptacle.

Before use, check whether the grid voltage is consistent with the voltage value marked on the product.

If you don't have enough knowledge about electrical connection, please __t31__.

Installation method

__t33__ remove the old faucet.

Make the connection to the appropriate water line.

Install the __t34__ between the main water supply line and the faucet's water inlet.

__t35__ turn on the water by turning the knob on the faucet.

__t36__ at the connection points.

If there are no leaks, proceed to the electrical connection stage.

__t37__ connect the electrical connection of the faucet.

Secure the electrical cord to the wall with a cable clip.

Do not damage the electrical cable when securing the cable.

__t38__ when you turn the knob to the hot water zone:

• The digital display works.
• It shows the water temperature.
• The heating process begins.

When you turn the knob to the cold water zone:

• The digital display goes off.
• The heating process stops.

Method of Use

1. the use of faucet handle

The faucet handle is turned to adjust between the hot and cold water zone.

2. temperature indicator

The digital display shows the water temperature (__t46__) and also indicates the product's operating status.

• If the screen is lit →Heating works.
• When heating stops → the display turns off/extinguishes.

3. faucet spout / nozzle cleaning

The spout tip should be cleaned regularly.

The nozzle can be disassembled and washed under water.if dirt or limescale cannot be removed from the inside, the holes can be carefully cleaned with a suitable thin tool/needle.

4. regular cleaning of the heating pipe

The lid of the product should be opened and any dirt and limescale deposits that may have accumulated in the heating section should be carefully cleaned.

__t49__ the product must be disconnected from the electrical connection during this process.

Failure causes and troubleshooting

Issue	Possible reason	Solution
The water is not heating up	No power or very low water pressure.	Check the electrical connection. ensure the water pressure is __t59__.
The water temperature is low	The water pressure is too high or the mains voltage is low.	Reduce the amount of water output and check the mains voltage.
The water temperature is too high, the water flow is small	The water inlet is blocked or the water pressure is low.	Check and clean the filter/dirt trap on the water inlet. if the issue persists, the water pressure may be too low.
The temperature indicator is not lighting up	Water pressure is too low, there may be a fault in the electrical circuit or a fault in the faucet.	Restore water pressure to normal. check the electrical circuit. if the problem persists, contact an authorized service technician.