Generic Brand Granite Wind White Mountaineer Helmet

Delta plus granite wind mountaineer helmet features a twist-to-release mechanism adjustable from 53-63 cm enhanced air channels wide field of vision automatic opening when the adjustment screw is pulled alphabetical label industrial safety helmets complies with the basic conditions of the 89/686/eec directive and the general conditions of the en397:1995/a1:2000 & en50365:2002 (granite peak only) regulations. Use of protective helmetthis helmet, after a impact, the energy generated by the partial destruction of the cap or seat belt or damage! It is designed to be absorbed through. Even if such damage is not immediately obvious, it is recommended to replace the helmet that has received a strong shock. To ensure adequate protection, this helmet should be adjusted or adapted to the user's head. We would also like to point out that any modifications to the protective helmet or the removal of any of its original parts (beyond modifications or alterations recommended by the helmet manufacturer) could be dangerous. Helmets should never be subjected to any process other than those recommended by the helmet manufacturer for adjustment or adding accessories. Never apply paint, solvents, adhesives or glues to helmet unless specifically recommended by the helmet manufacturer. Electrical usage restrictions and precautions before use, the user should check the electrical restrictions of the helmet according to the nominal voltage that may be encountered during use. Insulated helmets should not be used in situations where there is a risk of gradually reducing the helmet's insulation properties. Their electrical insulating performance is only valid if this helmet is used alone: other insulating protective equipment must be used in addition, in accordance with the risks involved in the work. After use: if the helmet's exterior becomes partially soiled, it should be carefully cleaned according to the following recommendations (maintenance/storage). Protective helmet adjustment and inspection to provide effective protection, the helmet should be worn with the sunshade front (placed on the flat head) and adjusted according to the size of the user's head (neither too tight nor too loose) head equal and comfortable (adjustable head circumference between 53 and 63 cm) by turning the knob in the clockwise direction as much as the helmet is positioned. The lifespan of a helmet is affected by factors such as cold, heat, chemical products, sunlight, and misuse. Daily and before each use, the helmet, straps, and breakable accessories should be checked for any signs of cracks or defects. A helmet that has suffered a strong shock or that shows signs of wear should be replaced. If there is no flaw, it is suitable for use. The manufacture date can be found on the inside of the helmet. Under normal conditions of use, this protective helmet provides effective protection for up to 4 years from the date of first use or 7 years from the date of manufacture. Maintenance / storage: this protective helmet can be wiped down and disinfected with a cloth dampened with a low-concentration cleaning solution. Do not use corrosive or rust-inducing chemical products. If the helmet cannot be cleaned by this method, it should be replaced. The product should be transported in its own packaging. If there is no packaging unit, select a packaging that will protect the product from shock, exposure to moisture, thermal hazards, light, and keep it away from materials or substances that may deteriorate the product. The helmet should be stored in a dry place away from light and ice, and should not be stored in a way that sharp objects or chemical products can spill on it, either when not in use or during transportation. It should not be compressed or stored near a heat source. 20±15 ° It is recommended to store within the c temperature range. This helmet does not contain any known allergens. If an allergic reaction occurs, the individual should leave the hazardous area, remove the helmet, and seek medical assistance. Caution: omissions or errors in the adjustment/inspections and care/storage operating instructions can affect the efficiency of the insulation protection. Accessories and spare parts accessories and spare parts (such as sweatbands, seatbelt components, chin straps, hearing protectors, etc.) where applicable. Supplied with installation instructions. Marking (optional test) a helmet displaying one of these markings meets the following requirements: -20 ° C / -30 ° C: very low temperature maintains helmet performance above these temperatures. 440vac: electrical insulation protects the user in the event of short-term, unintentional contact with electricity up to 440 volts (ac). For general use in industry and for works with electrical risks up to 440v. Mm: melted metal splashes helmet (headgear) protects the user against molten metal splashes. Class 0 electrical test (en 50365:2002) the helmet provides electrical insulation and can be used when working with electrical parts or in the immediate vicinity of electrical parts that do not exceed 1000v ac or 1500v dc. When used in conjunction with other electrical insulating protective equipment, this helmet prevents dangerous current from passing over the head.