ANENG B22 Black Voltage Screwdriver Tester Pen Rechargeable Digital Non-contact 30~1000V Detec

ANENG Digital Voltage Screwdriver Tester Pen Rechargeable B22 Non-contact 30~1000V Detection Household Electrician Repair Tools

Overview:

This electric tester is designed and produced according to the safety requirements of the international electrical safety standard IEC-61010 for electronic measuring instruments and handheld digital multimeters.

Meets the requirements of 600V CAT IV, 1000V CAT III, and Pollution Level 2 for lEC61010.

Before using this instrument, please read the user manual carefully and pay attention to the relevant safety work guidelines.

B22 Parameters:

AC Voltage Range	Non-contact Measurement:30~1000V;Contact Measurement:3V~600V
Frequency	50~60Hz
Alarm Mode	Screen Backlight Color Change+Audible Alarm
Live/Neutral Wire Identification	The one with higher electric field intensity or voltage value is the live wire
Inductive Sensitivity Indication	3-level Scale Indication:"-"for Weak Electric Field;"--"for Medium Electric Field;"---"for Strong Electric Field
Continuity Test	Conductor Continuity:Screen displays 0 with buzzer beep
Auto Power Off	The test pen will auto power off after 5 minutes of inactivity upon startup
NCV Voltage Detection	√
Phillips/Flathead Screwdriver	√
Retractable Bit	√
Two-way Ratchet	√
Battery Low Voltage	√
Data Hold	√
Safety Rating	CE CAT.II 1000V/CAT.IV 600V
Power Supply	14500 Batteryx1,300mAh,3.7V
Insulated Rubber-coated Handle	√
Backlight On	√
Dual-color Digital Display	√

THE PARAMETERS ARE FOR REFERENCE ONLY, AND THE ACTUAL MEASUREMENT OF THE SPECIFIC EQUIPMENT SHALL PREVAIL!

Packing:

1 * Test Pen

1 * Packing box

1 * Storage bag

1 * Manual

1 * Charging cable

Safe work habits

*If the test pen is used near equipment with high electromagnetic interference, the measurement results may have significant errors.

*When the appearance of the electric pen is damaged, please do not use it.

*Extreme care must be taken when working around exposed conductors or buses.

*When the measured voltage exceeds the effective value of 60Vdc or 30Vac, please handle with caution to prevent electric shock.

*When using a voltage tester, do not touch the metal parts of the batch head with your hands to avoid electric shock and personal injury.

Steps for installing the battery:

After opening the battery cover, follow the instructions to insert a 14500 battery. (Note: If the positive and negative directions of the battery are reversed, it cannot be charged, otherwise it will damage the electric pen)

User Guide

1Touch and switch key function

After startup, it defaults to non-contact voltage measurement mode. Press and hold the [touch key] to switch to digital contact voltage measurement mode; If the screen displays a valid value (non-zero), releasing the button will automatically lock the value. If there is no valid reading when released, return to non-contact measurement mode. After locking, press and hold the switch button again to re-enter the digital contact voltage measurement mode.

2Non Contact Measurement (NCV)

By default, the device enters non-contact voltage measurement mode when turned on, with EF displayed on the screen. Hold the pen body with one hand and ensure that the human body is in full contact with the [touch key] (cannot be pressed). Use the pen head to sense possible charged objects. If the conductor is charged and the AC electric field strength around the charged conductor is sufficient for the pen to recognize, the display screen will show the corresponding induced voltage strength and color based on the strength of the electric field, and the internal buzzer will sound an alarm.

3Contact measurement and on-off measurement

By default, the device enters non-contact voltage measurement mode when turned on. Press and hold the [touch key] with bare hands to enter the digital contact voltage measurement and automatic recognition mode for on/off, and the screen displays oL.

1) Digital voltage measurement: Press the [touch button] with bare hands and use the batch head to touch possible charged objects. If the conductor is charged and the charged voltage is ≥ 3V AC voltage, the display screen will display the corresponding contact voltage value and color according to the voltage level, and the internal buzzer will sound an alarm. Release the button to lock the current value for easy reading.

2) On/off measurement: Press the [touch button] with bare hands, and make full contact with one end of the uncharged wire with the other hand. Use the pen tip to touch the exposed part of the wire at the other end. If the wire is connected, the pen will display 0 and the buzzer will sound.