Free shipping
Delivery address
Free shipping
Local delivery
Estimated delivery: 22 - 24 October
Select your address, find out the delivery date!
Trendyol's commitments
Easy and free return in 15 days.
Payment methods
Highlighted features:
Generic 7B4 5V Stepper Motor 28BYJ-48 + Drive Module Board features
Other Features
Easy motor wire connection, Easy to use with Arduino or other development platforms, Four-phase LED status indicator, Pluggable standard interface, Suitable for guide wind deflector and portable air conditioner valve, Supports direct plug and easy-to-use stepper motor in development board
Instructions for Use/Warnings
USES: ULN2003 Stepper Motor Driver Board uses the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or another development platform to drive the stepper motor by this diver board. Stepper Motor Wiring: 1. A 4-way input of I1, I2, I3, and I4 corresponds to the 4 IO lines of MCU. 2. The motor stepper directly plugs into the motor interface, pay attention to the socket groove joints corresponding to the convex side.
Blue PCB Electronics
7.8
Seller information
Shoppers also viewed
Set of 4 Lined Notebooks 13 X 20 Cm 56 Sheets Cardboard Cover Spiral Notebook Notebook Line Series
Generic 7B4 5V Stepper Motor 28BYJ-48 + Drive Module Board reviews
No reviews yet.
Product details
Product description
Description The ULN2003 is one of the most common motor driver ICs, consisting of an array of 7 Darlington transistor pairs, each pair is capable of driving loads of up to 500mA and 50V.
The board has a connector that mates the motor wires perfectly which makes it very easy to connect the motor to the board.
USES: ULN2003 Stepper Motor Driver Board uses the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v).
It's easy to use Arduino or another development platform to drive the stepper motor by this diver board.
A Stepper Motor Driver is the driver circuit that enables the stepper motor to function the way it does.
For example, stepper motors require sufficient and controlled energy for phases in a precise sequence.
Due to this, stepper motors are considered more advanced than the typical DC motor.
Features Dimensions of the board: approx.
35mm x 31mm.
Stepper motor driver board with an ULN2003 chip.
A four-phase LED indicates the status of the stepper motor.
Stepper motor with a standard interface, when used directly, is pluggable.
Stepper Motor Color: Silver Diameter: 28mm Voltage: 5V No-load pull into the frequency: >
600 Hz Phase: 4 No-load pull-out frequency: >
1000 Hz reduction ratio: 1/64 Pull-in torque: >
34.3 mN.
m.
(120Hz) Step Angle: 5.625 x 1/64 Self-positioning torque: >
34.3mN.
m DCR: 200ohm +/- 7% (25 °C) Temperature: <
40K (120Hz) Insulation resistance: >
10 ohm (500 volts) Noise: <
40dB (120Hz, No load, 10cm) Dielectric Strength: AC 600V, 1mA, 1s Insulation Class: A Cable length: 24cm Suitable for guide wind deflector, portable air conditioner valve, etc Dimensions: 1.65 in x 1.22 in x 0.79 in (4.2 cm x 3.1 cm x 2.0 cm) Weight: 1.20 oz (34 g) The 5 Line 4 phase can be driven by ordinary ULN2003 chip, can also be connected in phase 2 development board.
supporting the use of a direct plug and easy-to-use stepper motor used in the development board.
Stepper Motor Wiring 1. A 4-way input of I1, I2, I3, and I4 corresponds to the 4 IO lines of MCU.
2. The motor stepper directly plugs into the motor interface, pay attention to the socket groove joints corresponding to the convex side.
Package Includes ● 1 x ULN2003 Drive Board ● 1 x 5V Stepper Motor 28BYJ-48
Additional info
- Sold by .
- A maximum of 5 units of this product can be ordered. Trendyol reserves the right to cancel orders over 5 units.
- Barcode No: 2900000008809
Generic 7B4 5V Stepper Motor 28BYJ-48 + Drive Module Board features
Other Features
Easy motor wire connection, Easy to use with Arduino or other development platforms, Four-phase LED status indicator, Pluggable standard interface, Suitable for guide wind deflector and portable air conditioner valve, Supports direct plug and easy-to-use stepper motor in development board
Instructions for Use/Warnings
USES: ULN2003 Stepper Motor Driver Board uses the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or another development platform to drive the stepper motor by this diver board. Stepper Motor Wiring: 1. A 4-way input of I1, I2, I3, and I4 corresponds to the 4 IO lines of MCU. 2. The motor stepper directly plugs into the motor interface, pay attention to the socket groove joints corresponding to the convex side.
Safety information
Product safety information