Free shipping
Delivery address
Free shipping
Local delivery
Estimated delivery: 20 - 22 October
Select your address, find out the delivery date!
Trendyol's commitments
Easy and free return in 15 days.
Payment methods
Highlighted features:
Generic 2C2 650nm Laser Transmitter Module KY-008 features
Other Features
Arduino compatible, interactive laser pointer and simple projection capabilities, composed of 650nm red laser diode head, resistor, and 3 male header pins
Instructions for Use/Warnings
NB: The signals on the module may be incorrectly indicated, if the module does not work properly, connect [S] to GND and the [-] to +5VDC. Handle with caution, do not point the laser beam directly to the eyes. Connect the module signal pin (S) to pin 13 on the Arduino and ground (-) to GND. The middle pin on the module is not used. The following Arduino sketch is a laser blinker. It will continually turn the laser on and off in one second intervals: int laserPin = 13; void setup() { pinMode(laserPin, OUTPUT); } void loop() { digitalWrite(laserPin, HIGH); delay(1000); digitalWrite(laserPin, LOW); delay(1000); }
Blue PCB Electronics
7.8
Seller information
Generic 2C2 650nm Laser Transmitter Module KY-008 reviews
No reviews yet.
Product details
Product description
Description This small laser transmitter module works on 5V.
The laser outputs a beam of 650nm (red) of approximately 5mW.
Connect this module to a motor as an interactive laser pointer.
By moving the laser quickly, it is also possible to make a simple projection.
NB: The signals on the module may be incorrectly indicated, if the module does not work properly, connect [S] to GND and the [-] to +5VDC.
Properties Brand information Brand Opencircuit house brand Model 10227 Size info Length 15 mm Width 24 mm Height 8 mm Weight 2,2 g Specifications This module consists of a 650nm red laser diode head, a resistor and 3 male header pins.
Handle with caution, do not point the laser beam directly to the eyes.
Operating Voltage 5V Output Power 5mW Wavelenght 650nm Operating Current <
40mA Working Temperature 10°C ~ 40°C [14°F to 104°F] Board Dimensions 18.5mm x 15mm [0.728in x 0.591in] Connection Diagram Connect the module signal pin (S) to pin 13 on the Arduino and ground (-) to GND.
The middle pin on the module is not used.
KY-008 Arduino S Pin 13 middle – GND KY-008 Arduino code The following Arduino sketch is a laser blinker.
It will continually turn the laser on and off in one second intervals.
int laserPin = 13
void setup() { pinMode(laserPin, OUTPUT)
// Define the digital output interface pin 13 } void loop() { digitalWrite(laserPin, HIGH)
// Turn on the laser head delay(1000)
// wait for one second digitalWrite(laserPin, LOW)
// Turn off the laser head delay(1000)
Additional info
- Sold by .
- A maximum of 5 units of this product can be ordered. Trendyol reserves the right to cancel orders over 5 units.
- Barcode No: 2900000008991
Generic 2C2 650nm Laser Transmitter Module KY-008 features
Other Features
Arduino compatible, interactive laser pointer and simple projection capabilities, composed of 650nm red laser diode head, resistor, and 3 male header pins
Instructions for Use/Warnings
NB: The signals on the module may be incorrectly indicated, if the module does not work properly, connect [S] to GND and the [-] to +5VDC. Handle with caution, do not point the laser beam directly to the eyes. Connect the module signal pin (S) to pin 13 on the Arduino and ground (-) to GND. The middle pin on the module is not used. The following Arduino sketch is a laser blinker. It will continually turn the laser on and off in one second intervals: int laserPin = 13; void setup() { pinMode(laserPin, OUTPUT); } void loop() { digitalWrite(laserPin, HIGH); delay(1000); digitalWrite(laserPin, LOW); delay(1000); }
Safety information
Product safety information